DuPont™ Hytrel® HTR8068
THERMOPLASTIC POLYESTER ELASTOMER
Product Information
Common features of Hytrel® thermoplastic polyester elastomer include mechanical and physical properties such as exceptional toughness and resilience, high resistance to creep, impact and flex fatigue, flexibility at low temperatures and good retention of properties at elevated temperatures. In addition, it resists many industrial chemicals, oils and solvents. Special grades include heat stabilised, flame retardant, food contact compliant, blow molding and extrusion grades. Concentrates offered include black pigments, UV protection additives, heat stabilisers, and flame retardants.
Hytrel® thermoplastic polyester elastomer is plasticiser free.
The good melt stability of Hytrel® thermoplastic polyester elastomer normally enables the recycling of properly handled production waste. If recycling is not possible, DuPont recommends, as the preferred option, incineration with energy recovery (-24 kJ/g of base polymer) in appropriately equipped installations.
For disposal, local regulations have to be observed.
Hytrel® thermoplastic polyester elastomer typically is used in demanding applications in the automotive, fluid power, electrical/electronic, consumer goods, appliance and power tool, sporting goods, furniture, industrial and off-road transportation/equipment industry.
Hytrel® HTR8068 is a medium modulus flame retardant and antidrip Hytrel® resin that meets the requirement of UL94 V-0. It has nominal durometer hardness of 44D.



Processing Texts
Injection molding
PREPROCESSING
Drying recommended = Yes
Drying temperature = 80°C
Drying time, dehumidified dryer = 2-3 h
Processing moisture content = <0.08 %
PROCESSING
Melt temperature optimum = 200°C
Mould temperature optimum = 40°C
Mould temperature range = 30-40°C
Profile extrusion
PREPROCESSING
Drying recommended = Yes
Drying temperature = 80°C
Drying time, dehumidified dryer = 2-3 h
Processing moisture content = <0.06 %
PROCESSING
Melt temperature optimum = 195°C
Chemical Media Resistance
Acids
Acetic Acid (5% by mass) (23°C)
Citric Acid solution (10% by mass) (23°C)
Lactic Acid (10% by mass) (23°C)
Hydrochloric Acid (36% by mass) (23°C)
Nitric Acid (40% by mass) (23°C)
Sulfuric Acid (38% by mass) (23°C)
Sulfuric Acid (5% by mass) (23°C)
Chromic Acid solution (40% by mass) (23°C)
Bases
Sodium Hydroxide solution (35% by mass) (23°C)
Sodium Hydroxide solution (1% by mass) (23°C)
Ammonium Hydroxide solution (10% by mass) (23°C)
Alcohols
Isopropyl alcohol (23°C)
Methanol (23°C)
Ethanol (23°C)
Hydrocarbons
n-Hexane (23°C) Toluene (23°C) iso-Octane (23°C)
Ketones
Acetone (23°C)
Ethers
Diethyl ether (23°C)
Mineral oils
SAE 10W40 multigrade motor oil (23°C)
SAE 10W40 multigrade motor oil (130°C)
SAE 80/90 hypoid-gear oil (130°C)
Insulating Oil (23°C)
Standard Fuels
ISO 1817 Liquid 1 - E5 (60°C)
ISO 1817 Liquid 2 - M15E4 (60°C)
ISO 1817 Liquid 3 - M3E7 (60°C)
ISO 1817 Liquid 4 - M15 (60°C)
Standard fuel without alcohol (pref. ISO 1817 Liquid C) (23°C)
Standard fuel with alcohol (pref. ISO 1817 Liquid 4) (23°C)
Diesel fuel (pref. ISO 1817 Liquid F) (23°C)
Diesel fuel (pref. ISO 1817 Liquid F) (90°C)
Diesel fuel (pref. ISO 1817 Liquid F) (>90°C)
Salt solutions
Sodium Chloride solution (10% by mass) (23°C)
Sodium Hypochlorite solution (10% by mass) (23°C)
Sodium Carbonate solution (20% by mass) (23°C)
Sodium Carbonate solution (2% by mass) (23°C)
Zinc Chloride solution (50% by mass) (23°C)
Other
Ethyl Acetate (23°C) Hydrogen peroxide (23°C) DOT No. 4 Brake fluid (130°C)
Ethylene Glycol (50% by mass) in water (108°C)
1% nonylphenoxy-polyethyleneoxy ethanol in water (23°C)
50% Oleic acid + 50% Olive Oil (23°C) Water (23°C)
Water (90°C)
Phenol solution (5% by mass) (23°C)
Symbols used:
possibly resistant
Defined as: Supplier has sufficient indication that contact with chemical can be potentially accepted under the intended use conditions and expected service life. Criteria for assessment have to be indicated (e.g. surface aspect, volume change, property change).
not recommended - see explanation
Defined as: Not recommended for general use. However, short-term exposure under certain restricted conditions could be acceptable (e.g. fast cleaning with thorough rinsing, spills, wiping, vapor exposure).
Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc. ISO Mechanical properties measured at 4.0mm (Hytrel® measured at 2 mm), IEC Electrical properties measured at 2.0mm, all ASTM properties measured at 3.2mm, and test temperatures are 23°C unless otherwise stated.
The information set forth herein is furnished free of charge and is based on technical data that DuPont believes to be reliable and falls within the normal range of properties. It is intended for use by persons having technical skill, at their own discretion and risk. This data should not be used to establish specification limits nor used alone as the basis of design. Handling precaution information is given with the understanding that those using it will satisfy themselves that their particular conditions of use present no health or safety hazards. Since conditions of product use and disposal are outside our control, we make no warranties, express or implied, and assume no liability in connection with any use of this information. As with any product, evaluation under end-use conditions prior to specification is essential. Nothing herein is to be taken as a license to operate or a recommendation to infringe on patents. Caution: Do not use in medical applications involving permanent implantation in the human body. For other medical applications, discuss with your DuPont customer representative and read Medical Caution H-50103-4.
Copyright © 2014 DuPont or its affiliates. All Rights Reserved. The DuPont Oval Logo, DuPont™, The miracles of science™ and all products denoted with ® or ™ are registered trademarks or trademarks of E.I. du Pont de Nemours and Company or its affiliates.
THERMOPLASTIC POLYESTER ELASTOMER

Product Information
Common features of Hytrel® thermoplastic polyester elastomer include mechanical and physical properties such as exceptional toughness and resilience, high resistance to creep, impact and flex fatigue, flexibility at low temperatures and good retention of properties at elevated temperatures. In addition, it resists many industrial chemicals, oils and solvents. Special grades include heat stabilised, flame retardant, food contact compliant, blow molding and extrusion grades. Concentrates offered include black pigments, UV protection additives, heat stabilisers, and flame retardants.
Hytrel® thermoplastic polyester elastomer is plasticiser free.
The good melt stability of Hytrel® thermoplastic polyester elastomer normally enables the recycling of properly handled production waste. If recycling is not possible, DuPont recommends, as the preferred option, incineration with energy recovery (-24 kJ/g of base polymer) in appropriately equipped installations.
For disposal, local regulations have to be observed.
Hytrel® thermoplastic polyester elastomer typically is used in demanding applications in the automotive, fluid power, electrical/electronic, consumer goods, appliance and power tool, sporting goods, furniture, industrial and off-road transportation/equipment industry.
Hytrel® HTR8068 is a medium modulus flame retardant and antidrip Hytrel® resin that meets the requirement of UL94 V-0. It has nominal durometer hardness of 44D.

General information | Value | Unit | Test Standard |
Resin Identification | TPC-ET-FR(17) | - | ISO 1043 |
Part Marking Code | >TPC-ET-FR(17)< | - | ISO 11469 |
Rheological properties | Value | Unit | Test Standard |
Melt volume-flow rate | 3.6 | cm³/10min | ISO 1133 |
Temperature | 190 | °C | ISO 1133 |
Load | 2.16 | kg | ISO 1133 |
Melt mass-flow rate | 4 | g/10min | ISO 1133 |
Melt mass-flow rate, Temperature | 190 | °C | - |
Melt mass-flow rate, Load | 2.16 | kg | - |
Moulding shrinkage, parallel | 1.1 | % | ISO 294-4, 2577 |
Moulding shrinkage, normal | 1.1 | % | ISO 294-4, 2577 |
Mechanical properties (TPE) | Value | Unit | Test Standard |
Tensile Modulus | 140 | MPa | ISO 527-1/-2 |
Stress at 10% strain | 5.9 | MPa | ISO 527-1/-2 |
Stress at 50% strain | 7.3 | MPa | ISO 527-1/-2 |
Stress at break | 13 | MPa | ISO 527-1/-2 |
Strain at break | >300 | % | ISO 527-1/-2 |
Nominal strain at break | 340 | % | ISO 527-1/-2 |
Tear strength, parallel | 70 | kN/m | ISO 34-1 |
Tear strength, normal | 70 | kN/m | ISO 34-1 |
Shore D hardness, max | 44 | - | ISO 868 |
Shore D hardness, 15s | 38 | - | ISO 868 |
Mechanical properties | Value | Unit | Test Standard |
Flexural Modulus | 155 | MPa | ISO 178 |
Charpy notched impact strength | ISO 179/1eA | ||
23°C | 40 | kJ/m² | |
-30°C | 7 | kJ/m² | |
-40°C | 5 | kJ/m² | |
Brittleness temperature | -48 | °C | ISO 974 |
Thermal properties | Value | Unit | Test Standard |
Melting temperature, 10°C/min | 170 | °C | ISO 11357-1/-3 |
Temp. of deflection under load | ISO 75-1/-2 | ||
1.8 MPa | 41 | °C | |
0.45 MPa | 46 | °C |
Vicat softening temperature, 50°C/h, 10N | 107 | °C | ISO 306 |
Coeff. of linear therm. expansion, parallel | 150 | E-6/K | ISO 11359-1/-2 |
Coeff. of linear therm. expansion, normal | 170 | E-6/K | ISO 11359-1/-2 |
Eff. thermal diffusivity | 5.44E-8 | m²/s | - |
RTI, electrical, 1.5mm | 50 | °C | UL 746B |
RTI, impact, 1.5mm | 50 | °C | UL 746B |
RTI, strength, 1.5mm | 50 | °C | UL 746B |
Flammability | Value | Unit | Test Standard |
Burning Behav. at 1.5mm nom. thickn. | V-0 | class | IEC 60695-11-10 |
Thickness tested | 1.5 | mm | IEC 60695-11-10 |
UL recognition | UL | - | - |
Oxygen index | 26 | % | ISO 4589-1/-2 |
Electrical properties | Value | Unit | Test Standard |
CTI, 23°C, 3.0mm | 425 | PLC | UL 746A |
High Amperage Arc Ignition Resistance, 1.5 mm | 200 | arcs | UL 746A |
Other properties | Value | Unit | Test Standard |
Density | 1430 | kg/m³ | ISO 1183 |
Density of melt | 1300 | kg/m³ | - |
Water Absorption, Immersion 24h | 1.9 | % | ASTM D 570 |




Characteristics | |||
Injection Moulding | Sheet Extrusion | Casting | |
Processing | Film Extrusion | Other Extrusion | Thermoforming |
Profile Extrusion | Coatable | ||
Delivery form | Pellets | ||
Special characteristics | Light stabilised or stable | ||
to light | |||
Regional Availability | North America | Asia Pacific | Near East/Africa |
Europe | South and Central America | Global | |
Processing Texts
Injection molding
PREPROCESSING
Drying recommended = Yes
Drying temperature = 80°C
Drying time, dehumidified dryer = 2-3 h
Processing moisture content = <0.08 %
PROCESSING
Melt temperature optimum = 200°C
Mould temperature optimum = 40°C
Mould temperature range = 30-40°C

Profile extrusion
PREPROCESSING
Drying recommended = Yes
Drying temperature = 80°C
Drying time, dehumidified dryer = 2-3 h
Processing moisture content = <0.06 %
PROCESSING
Melt temperature optimum = 195°C
Chemical Media Resistance

Acids

Acetic Acid (5% by mass) (23°C)

Citric Acid solution (10% by mass) (23°C)

Lactic Acid (10% by mass) (23°C)
Hydrochloric Acid (36% by mass) (23°C)
Nitric Acid (40% by mass) (23°C)
Sulfuric Acid (38% by mass) (23°C)
Sulfuric Acid (5% by mass) (23°C)

Chromic Acid solution (40% by mass) (23°C)

Bases

Sodium Hydroxide solution (35% by mass) (23°C)

Sodium Hydroxide solution (1% by mass) (23°C)

Ammonium Hydroxide solution (10% by mass) (23°C)
Alcohols
Isopropyl alcohol (23°C)
Methanol (23°C)
Ethanol (23°C)
Hydrocarbons
n-Hexane (23°C) Toluene (23°C) iso-Octane (23°C)
Ketones

Acetone (23°C)

Ethers

Diethyl ether (23°C)

Mineral oils

SAE 10W40 multigrade motor oil (23°C)

SAE 10W40 multigrade motor oil (130°C)
SAE 80/90 hypoid-gear oil (130°C)
Insulating Oil (23°C)

Standard Fuels
ISO 1817 Liquid 1 - E5 (60°C)
ISO 1817 Liquid 2 - M15E4 (60°C)
ISO 1817 Liquid 3 - M3E7 (60°C)
ISO 1817 Liquid 4 - M15 (60°C)
Standard fuel without alcohol (pref. ISO 1817 Liquid C) (23°C)

Standard fuel with alcohol (pref. ISO 1817 Liquid 4) (23°C)
Diesel fuel (pref. ISO 1817 Liquid F) (23°C)

Diesel fuel (pref. ISO 1817 Liquid F) (90°C)

Diesel fuel (pref. ISO 1817 Liquid F) (>90°C)

Salt solutions

Sodium Chloride solution (10% by mass) (23°C)

Sodium Hypochlorite solution (10% by mass) (23°C)
Sodium Carbonate solution (20% by mass) (23°C)

Sodium Carbonate solution (2% by mass) (23°C)

Zinc Chloride solution (50% by mass) (23°C)

Other

Ethyl Acetate (23°C) Hydrogen peroxide (23°C) DOT No. 4 Brake fluid (130°C)
Ethylene Glycol (50% by mass) in water (108°C)
1% nonylphenoxy-polyethyleneoxy ethanol in water (23°C)

50% Oleic acid + 50% Olive Oil (23°C) Water (23°C)
Water (90°C)
Phenol solution (5% by mass) (23°C)
Symbols used:

Defined as: Supplier has sufficient indication that contact with chemical can be potentially accepted under the intended use conditions and expected service life. Criteria for assessment have to be indicated (e.g. surface aspect, volume change, property change).

Defined as: Not recommended for general use. However, short-term exposure under certain restricted conditions could be acceptable (e.g. fast cleaning with thorough rinsing, spills, wiping, vapor exposure).
Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc. ISO Mechanical properties measured at 4.0mm (Hytrel® measured at 2 mm), IEC Electrical properties measured at 2.0mm, all ASTM properties measured at 3.2mm, and test temperatures are 23°C unless otherwise stated.
The information set forth herein is furnished free of charge and is based on technical data that DuPont believes to be reliable and falls within the normal range of properties. It is intended for use by persons having technical skill, at their own discretion and risk. This data should not be used to establish specification limits nor used alone as the basis of design. Handling precaution information is given with the understanding that those using it will satisfy themselves that their particular conditions of use present no health or safety hazards. Since conditions of product use and disposal are outside our control, we make no warranties, express or implied, and assume no liability in connection with any use of this information. As with any product, evaluation under end-use conditions prior to specification is essential. Nothing herein is to be taken as a license to operate or a recommendation to infringe on patents. Caution: Do not use in medical applications involving permanent implantation in the human body. For other medical applications, discuss with your DuPont customer representative and read Medical Caution H-50103-4.
Copyright © 2014 DuPont or its affiliates. All Rights Reserved. The DuPont Oval Logo, DuPont™, The miracles of science™ and all products denoted with ® or ™ are registered trademarks or trademarks of E.I. du Pont de Nemours and Company or its affiliates.